4000U USB Controller (Discontinued March 2006)

Merkmale

• Technische

  ---

  Artikelnummer(n)

  E14603-000

  Technologie

  AccuTouch® 5-Draht-Widerstandssensorik

  Abmessungen

  2.36" x 3.51" x 0.61" / 59.94 mm x 89.03 mm x 15.44 mm

  Schnittstelle

  USB High Speed
  Plug and play compatible

  Auflösung

  Approximately 4096x4096, size independent, 255 levels of Z (pressure)

  Conversion Time

  Approximately 20 ms per coordinate set

  Stromversorgung

  120 mA, typical at +5 VDC

  Eingangsspannung

  +5 VDC, nominal (+4.75 to +5.25 VDC)

  Baudrate

  +4.75 to +5.25 VDC

  Reliability

  MTBF greater than 500,000 hours per MIL-HDBK-217-F2 using the parts stress calculation method for the ground benign environment with an ambient temperature of 35°C

  Construction

  Four-layer surface-mount design with internal ground plane for EMI suppression

  Flammability

  The printed circuit board substrate is rated 94V0. All plastic components, such a headers and connectors, are also rated 94V0

  Shock and Vibration

  Three axis sine wave, 50Hz to 2kHz, 1G, 2 minutes/Octave with dwell on resonance

  ESD

  Per EN 6100-4-2 1995: Level 4. Contact discharge 8kV, air discharge 15kV

  LED Diagnostic Characteristics

  A green LED (D2) indicates controller status as follows:
  
  LED Blink Rate: Once per second
  Function: Normal condition, untouched state
  
  LED Blink Rate: On continuously
  Function: Touched state
  
  LED Blink Rate: Twice per second
  Function: Error detected
  
  A second LED (D1) indicates USB status as follows:
  
  LED State: OFF
  Function: Controller is not enumerated on USB
  
  LED State: ON
  Function: Controller is enumerated on USB, but there is no data transfer
  
  LED State: Blinking
  Function: USB data transfers between controller and host are occurring
  

  Orientation for USB Communication

  P2 pin #: 1 / Signal name: VBUS / Standard wire color: RED
  P2 pin #: 2 / Signal name: D- / Standard wire color: WHITE
  P2 pin #: 3 / Signal name: D+ / Standard wire color: GREEN
  P2 pin #: 4 / Signal name: GND / Standard wire color: BLACK
  P2 pin #: Shell / Signal name: Shield / Standard wire color: Drain Wire

  Betriebstemperatur

  -20°C to 70°C

  Betriebsumgebung

  CarrollTouch SmartSet protocol
  Initial/Stream/ Untouch/ Z-axis Enable Modes
  

  Lagertemperatur

  -48°C to 85°C

  Feuchtigkeit

  Operating: 10% to 90% RH, noncondensing
  Storage: 10% to 90% RH, noncondensing

  Höhe

  10,000 feet

  MTBF

  50.000 Stunden, nachgewiesen

  Zertifizierungen und Konformitätserklärungen

  Elo controllers are "CNR/USR" UL Recognized Components for USA and Canada, Category NWGQ2, Information Technology Equipment Including Business Equipment.
  Elo controllers are TUV Bauart certified as components.
  Elo controllers have been tested for compliance with FCC Part 15 Class B limits
  Depending on the application, it may be necessary to pay special attention to system grounding and shielding, and it may be necessary to apply ferrite suppressor beads.
  RoHS Declaration of Compliance

  Montageoptionen

  All mounting holes are plated through-holes for chassis ground connection. Refer to the drawings at the end of this document

  Connectors and Pin Definitions

  The connector configuration permits the controller to be placed in-line between the touchscreen and a USB hub or host attachment.